Call Today

The content which follows involving How to Install a Bathtub Yourself is definitely captivating. Don't miss out on it.

Mounting a bath tub isn't precisely brain surgery, but it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging project. If the old tub is conveniently easily accessible, the job can relocate easily; if you have to open a wall surface to eliminate the old tub and also place the new tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the work as well as are comfortable attempting it. Instead of hiring a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This post will help you mount a new bathtub in your washroom if you have actually already acquired a brand-new tub and do not need to change the setup of your previous supply of water pipelines.
Your devices and product list ought to consist of the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Setup

Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

Installing the Bathtub

Using the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bath tub till the level checks out level.
To install taps, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Activate the water as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bathtub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of a minimum of once as this will certainly settle it into its last position.

Suitable New Taps

If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Tiling Around the Tub

In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the market. It is advisable to fit the ceramic tiles making use of waterproof or water-proof glue and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I was guided to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on a different website. Do you know somebody else who is fascinated by the subject? Do not hesitate to promote it. Thank you for your time spent reading it.

Schedule Service Pickup